% Template for 3rd INTERNATIONAL CONFERENCE ON FLIGHT VEHICLES, AEROTHERMODYNAMICS AND RE-ENTRY (FAR); to be used with:
% --------------------------------------------------------------------------
\documentclass{FAR}
%==========================================================

% ---------------------------------------------------------
% DOCUMENT PROPERTIES
% ---------------------------------------------------------
\title{Template for the 3rd FAR Conferencelatex }


\author[1]{Author One}
\author[2]{Author Two}
\author[2]{Author Three}
\author[3]{Author Four}

\affil[1]{Affiliation One}
\affil[2]{Affiliation Two}
\affil[3]{Affiliation Three}

% ---------------------------------------------------------
% LOAD USER-SPECIFIC PACKAGES
% ---------------------------------------------------------



%==========================================================

\begin{document}
%
\maketitle
%
\begin{abstract}
The abstract should appear at the top of the left-hand column of text, about
0.5 inch (12 mm) below the title area and no more than 3.125 inches (80 mm) in
length.  Leave a 0.5 inch (12 mm) space between the end of the abstract and the
beginning of the main text.  The abstract should contain about 100 to 150
words, and should be identical to the abstract text submitted electronically
along with the paper cover sheet.  All manuscripts must be written in English.
\end{abstract}
%

\keywords{manuscript, latex, template, example}
%
\section{Introduction}
\label{sec:intro}

These guidelines include complete descriptions of the fonts, spacing, and
related information for producing your proceedings manuscripts. 

\section{Formatting your paper}
\label{sec:format}

All printed material, including text, illustrations, and charts, must be kept
within a print area of 7 inches (178 mm) wide by 9 inches (229 mm) high. Do
not write anything outside the print area. The top margin must be 1
inch (25 mm), except for the title page, and the left margin must be 0.75 inch
(19 mm).  All {\it text} must be in a two-column format. Columns are to be 3.39
inches (86 mm) wide, with a 0.24 inch (6 mm) space between them. Text must be
fully justified.

\section{Page title section}
\label{sec:pagestyle}

The paper title (on the first page) should begin 1.38 inches (35 mm) from the
top edge of the page, centered, completely capitalized, and in Times 14-point,
boldface type.  The authors' name(s) and affiliation(s) appear below the title
in capital and lower case letters.  Papers with multiple authors and
affiliations may require two or more lines for this information.

\section{TYPE-STYLE AND FONTS}
\label{sec:typestyle}

To achieve the best rendering, only use Times-Roman font. In addition, this will give
the proceedings a more uniform look.  Use a font that is no smaller than nine
point type throughout the paper, including figure captions.

In nine point type font, capital letters are 2 mm high.  {\bf If you use the
smallest point size, there should be no more than 3.2 lines/cm (8 lines/inch)
vertically.}  This is a minimum spacing; 2.75 lines/cm (7 lines/inch) will make
the paper much more readable.  Larger type sizes require correspondingly larger
vertical spacing.  Please do not double-space your paper.  TrueType or
Postscript Type 1 fonts are preferred.

The first paragraph in each section should not be indented, but all the
following paragraphs within the section should be indented as these paragraphs
demonstrate.

\section{MAJOR HEADINGS}
\label{sec:majhead}

Major headings, for example, "1. Introduction", should appear in all capital
letters, bold face if possible, centered in the column, with one blank line
before, and one blank line after. Use a period (".") after the heading number,
not a colon.

\subsection{Subheadings}
\label{ssec:subhead}

Subheadings should appear in lower case (initial word capitalized) in
boldface.  They should start at the left margin on a separate line.
 
\subsubsection{Sub-subheadings}
\label{sssec:subsubhead}

Sub-subheadings, as in this paragraph, are discouraged. However, if you
must use them, they should appear in lower case (initial word
capitalized) and start at the left margin on a separate line, with paragraph
text beginning on the following line.  They should be in italics.

\section{Printing your paper}
\label{sec:print}

The result of your paper shall be able to be printed in an A4 paper size. For this, please leave the extra 0.5 inch (12 mm) empty at the BOTTOM of the page and follow the top and left margins as specified. If the last page of your paper is only partially filled, arrange
the columns so that they are evenly balanced if possible, rather than having
one long column.

In LaTeX, to start a new column (but not a new page) and help balance the
last-page column lengths, you can use the command ``$\backslash$pagebreak'' as
demonstrated on this page (see the LaTeX source below).

\section{Page numbering}
\label{sec:page}

Please do {\bf not} paginate your paper.  Page numbers, session numbers, and
conference identification will be inserted when the paper is included in the
proceedings.

\section{Figures, tables, equations}
\label{sec:floats}

Figures, tables and equations must be numbered and placed within the designated margins. They may span the two
columns. Every figure and table must also be captioned.

If possible, position illustrations at the top of columns, rather than in the middle or at the bottom. Figure~\ref{fig:res} shows how to include images.



\begin{figure}[htb]
\begin{minipage}[b]{.48\linewidth}
  \centering
	\includegraphics[width=\linewidth]{img/screenshot1.png}
  \centerline{(a) Scenario 1}\medskip
\end{minipage}
\hfill
\begin{minipage}[b]{0.48\linewidth}
  \centering
	\includegraphics[width=\linewidth]{img/screenshot2.png}
  \centerline{(b) Scenario 2}\medskip
\end{minipage}
\caption{Example of placing a figure}
\label{fig:res}
\end{figure}

For tables, the example on how they shall be captioned and formatted is provided in Table~\ref{tab:res}.

\begin{table}[htb]
\centering
\caption{Example of formatting a table}\vspace{2mm}
\begin{tabular}{lll}
\hline\hline
Column A & Column B & Column C\\
\hline
Row 1 &  & \\
Row 2 &  & \\
Row 3 &  & \\
\hline\hline
\end{tabular}
\label{tab:res}
\end{table}


Equations shall be centred in the column and the corresponding number aligned on the right. They shall be referenced using parenthesis, e.g.,~\ref{eq:ellipse}.

\begin{equation}
r=\frac{p}{1+e\cos\theta}
\label{eq:ellipse}
\end{equation}

\section{FOOTNOTES}
\label{sec:foot}

Use footnotes sparingly (or not at all!) and place them at the bottom of the
column on the page on which they are referenced. Use Times 9-point type,
single-spaced. To help your readers, avoid using footnotes altogether and
include necessary peripheral observations in the text (within parentheses, if
you prefer, as in this sentence).

\bibliographystyle{IEEEbib}
\bibliography{refs}

\end{document}
